| .. | |||||
| dmasound | |||||
| Kconfig | |||||
| Makefile |
| Server IP : 104.21.87.198 / Your IP : 172.68.164.171 Web Server : Apache/2.2.15 (CentOS) System : Linux GA 2.6.32-431.1.2.0.1.el6.x86_64 #1 SMP Fri Dec 13 13:06:13 UTC 2013 x86_64 User : apache ( 48) PHP Version : 5.6.38 Disable Function : NONE MySQL : ON | cURL : ON | WGET : ON | Perl : ON | Python : ON | Sudo : ON | Pkexec : OFF Directory : /lib/modules/2.6.32-754.6.3.el6.x86_64/source/sound/oss/ |
Upload File : |
# drivers/sound/Config.in # # 18 Apr 1998, Michael Elizabeth Chastain, <mailto:mec@shout.net> # More hacking for modularisation. # # Prompt user for primary drivers. config SOUND_BCM_CS4297A tristate "Crystal Sound CS4297a (for Swarm)" depends on SIBYTE_SWARM help The BCM91250A has a Crystal CS4297a on synchronous serial port B (in addition to the DB-9 serial port). Say Y or M here to enable the sound chip instead of the UART. Also note that CONFIG_KGDB should not be enabled at the same time, since it also attempts to use this UART port. config SOUND_VWSND tristate "SGI Visual Workstation Sound" depends on X86_VISWS help Say Y or M if you have an SGI Visual Workstation and you want to be able to use its on-board audio. Read <file:Documentation/sound/oss/vwsnd> for more info on this driver's capabilities. config SOUND_AU1550_AC97 tristate "Au1550/Au1200 AC97 Sound" depends on SOC_AU1550 || SOC_AU1200 config SOUND_MSNDCLAS tristate "Support for Turtle Beach MultiSound Classic, Tahiti, Monterey" depends on (m || !STANDALONE) && ISA help Say M here if you have a Turtle Beach MultiSound Classic, Tahiti or Monterey (not for the Pinnacle or Fiji). See <file:Documentation/sound/oss/MultiSound> for important information about this driver. Note that it has been discontinued, but the Voyetra Turtle Beach knowledge base entry for it is still available at <http://www.turtlebeach.com/site/kb_ftp/790.asp>. comment "Compiled-in MSND Classic support requires firmware during compilation." depends on SOUND_PRIME && SOUND_MSNDCLAS=y config MSNDCLAS_HAVE_BOOT bool depends on SOUND_MSNDCLAS=y && !STANDALONE default y config MSNDCLAS_INIT_FILE string "Full pathname of MSNDINIT.BIN firmware file" depends on SOUND_MSNDCLAS default "/etc/sound/msndinit.bin" help The MultiSound cards have two firmware files which are required for operation, and are not currently included. These files can be obtained from Turtle Beach. See <file:Documentation/sound/oss/MultiSound> for information on how to obtain this. config MSNDCLAS_PERM_FILE string "Full pathname of MSNDPERM.BIN firmware file" depends on SOUND_MSNDCLAS default "/etc/sound/msndperm.bin" help The MultiSound cards have two firmware files which are required for operation, and are not currently included. These files can be obtained from Turtle Beach. See <file:Documentation/sound/oss/MultiSound> for information on how to obtain this. config MSNDCLAS_IRQ int "MSND Classic IRQ 5, 7, 9, 10, 11, 12" depends on SOUND_MSNDCLAS=y default "5" help Interrupt Request line for the MultiSound Classic and related cards. config MSNDCLAS_MEM hex "MSND Classic memory B0000, C8000, D0000, D8000, E0000, E8000" depends on SOUND_MSNDCLAS=y default "D0000" help Memory-mapped I/O base address for the MultiSound Classic and related cards. config MSNDCLAS_IO hex "MSND Classic I/O 210, 220, 230, 240, 250, 260, 290, 3E0" depends on SOUND_MSNDCLAS=y default "290" help I/O port address for the MultiSound Classic and related cards. config SOUND_MSNDPIN tristate "Support for Turtle Beach MultiSound Pinnacle, Fiji" depends on (m || !STANDALONE) && ISA help Say M here if you have a Turtle Beach MultiSound Pinnacle or Fiji. See <file:Documentation/sound/oss/MultiSound> for important information about this driver. Note that it has been discontinued, but the Voyetra Turtle Beach knowledge base entry for it is still available at <http://www.turtlebeach.com/site/kb_ftp/600.asp>. comment "Compiled-in MSND Pinnacle support requires firmware during compilation." depends on SOUND_PRIME && SOUND_MSNDPIN=y config MSNDPIN_HAVE_BOOT bool depends on SOUND_MSNDPIN=y default y config MSNDPIN_INIT_FILE string "Full pathname of PNDSPINI.BIN firmware file" depends on SOUND_MSNDPIN default "/etc/sound/pndspini.bin" help The MultiSound cards have two firmware files which are required for operation, and are not currently included. These files can be obtained from Turtle Beach. See <file:Documentation/sound/oss/MultiSound> for information on how to obtain this. config MSNDPIN_PERM_FILE string "Full pathname of PNDSPERM.BIN firmware file" depends on SOUND_MSNDPIN default "/etc/sound/pndsperm.bin" help The MultiSound cards have two firmware files which are required for operation, and are not currently included. These files can be obtained from Turtle Beach. See <file:Documentation/sound/oss/MultiSound> for information on how to obtain this. config MSNDPIN_IRQ int "MSND Pinnacle IRQ 5, 7, 9, 10, 11, 12" depends on SOUND_MSNDPIN=y default "5" help Interrupt request line for the primary synthesizer on MultiSound Pinnacle and Fiji sound cards. config MSNDPIN_MEM hex "MSND Pinnacle memory B0000, C8000, D0000, D8000, E0000, E8000" depends on SOUND_MSNDPIN=y default "D0000" help Memory-mapped I/O base address for the primary synthesizer on MultiSound Pinnacle and Fiji sound cards. config MSNDPIN_IO hex "MSND Pinnacle I/O 210, 220, 230, 240, 250, 260, 290, 3E0" depends on SOUND_MSNDPIN=y default "290" help Memory-mapped I/O base address for the primary synthesizer on MultiSound Pinnacle and Fiji sound cards. config MSNDPIN_DIGITAL bool "MSND Pinnacle has S/PDIF I/O" depends on SOUND_MSNDPIN=y help If you have the S/PDIF daughter board for the Pinnacle or Fiji, answer Y here; otherwise, say N. If you have this, you will be able to play and record from the S/PDIF port (digital signal). See <file:Documentation/sound/oss/MultiSound> for information on how to make use of this capability. config MSNDPIN_NONPNP bool "MSND Pinnacle non-PnP Mode" depends on SOUND_MSNDPIN=y help The Pinnacle and Fiji card resources can be configured either with PnP, or through a configuration port. Say Y here if your card is NOT in PnP mode. For the Pinnacle, configuration in non-PnP mode allows use of the IDE and joystick peripherals on the card as well; these do not show up when the card is in PnP mode. Specifying zero for any resource of a device will disable the device. If you are running the card in PnP mode, you must say N here and use isapnptools to configure the card's resources. comment "MSND Pinnacle DSP section will be configured to above parameters." depends on SOUND_MSNDPIN=y && MSNDPIN_NONPNP config MSNDPIN_CFG hex "MSND Pinnacle config port 250,260,270" depends on MSNDPIN_NONPNP default "250" help This is the port which the Pinnacle and Fiji uses to configure the card's resources when not in PnP mode. If your card is in PnP mode, then be sure to say N to the previous option, "MSND Pinnacle Non-PnP Mode". comment "Pinnacle-specific Device Configuration (0 disables)" depends on SOUND_MSNDPIN=y && MSNDPIN_NONPNP config MSNDPIN_MPU_IO hex "MSND Pinnacle MPU I/O (e.g. 330)" depends on MSNDPIN_NONPNP default "0" help Memory-mapped I/O base address for the Kurzweil daughterboard synthesizer on MultiSound Pinnacle and Fiji sound cards. config MSNDPIN_MPU_IRQ int "MSND Pinnacle MPU IRQ (e.g. 9)" depends on MSNDPIN_NONPNP default "0" help Interrupt request number for the Kurzweil daughterboard synthesizer on MultiSound Pinnacle and Fiji sound cards. config MSNDPIN_IDE_IO0 hex "MSND Pinnacle IDE I/O 0 (e.g. 170)" depends on MSNDPIN_NONPNP default "0" help CD-ROM drive 0 memory-mapped I/O base address for the MultiSound Pinnacle and Fiji sound cards. config MSNDPIN_IDE_IO1 hex "MSND Pinnacle IDE I/O 1 (e.g. 376)" depends on MSNDPIN_NONPNP default "0" help CD-ROM drive 1 memory-mapped I/O base address for the MultiSound Pinnacle and Fiji sound cards. config MSNDPIN_IDE_IRQ int "MSND Pinnacle IDE IRQ (e.g. 15)" depends on MSNDPIN_NONPNP default "0" help Interrupt request number for the IDE CD-ROM interface on the MultiSound Pinnacle and Fiji sound cards. config MSNDPIN_JOYSTICK_IO hex "MSND Pinnacle joystick I/O (e.g. 200)" depends on MSNDPIN_NONPNP default "0" help Memory-mapped I/O base address for the joystick port on MultiSound Pinnacle and Fiji sound cards. config MSND_FIFOSIZE int "MSND buffer size (kB)" depends on SOUND_MSNDPIN=y || SOUND_MSNDCLAS=y default "128" help Configures the size of each audio buffer, in kilobytes, for recording and playing in the MultiSound drivers (both the Classic and Pinnacle). Larger values reduce the chance of data overruns at the expense of overall latency. If unsure, use the default. menuconfig SOUND_OSS tristate "OSS sound modules" depends on ISA_DMA_API && VIRT_TO_BUS help OSS is the Open Sound System suite of sound card drivers. They make sound programming easier since they provide a common API. Say Y or M here (the module will be called sound) if you haven't found a driver for your sound card above, then pick your driver from the list below. if SOUND_OSS config SOUND_TRACEINIT bool "Verbose initialisation" help Verbose soundcard initialization -- affects the format of autoprobe and initialization messages at boot time. config SOUND_DMAP bool "Persistent DMA buffers" ---help--- Linux can often have problems allocating DMA buffers for ISA sound cards on machines with more than 16MB of RAM. This is because ISA DMA buffers must exist below the 16MB boundary and it is quite possible that a large enough free block in this region cannot be found after the machine has been running for a while. If you say Y here the DMA buffers (64Kb) will be allocated at boot time and kept until the shutdown. This option is only useful if you said Y to "OSS sound modules", above. If you said M to "OSS sound modules" then you can get the persistent DMA buffer functionality by passing the command-line argument "dmabuf=1" to the sound module. Say Y unless you have 16MB or more RAM or a PCI sound card. config SOUND_SSCAPE tristate "Ensoniq SoundScape support" help Answer Y if you have a sound card based on the Ensoniq SoundScape chipset. Such cards are being manufactured at least by Ensoniq, Spea and Reveal (Reveal makes also other cards). If you compile the driver into the kernel, you have to add "sscape=<io>,<irq>,<dma>,<mpuio>,<mpuirq>" to the kernel command line. config SOUND_VMIDI tristate "Loopback MIDI device support" help Support for MIDI loopback on port 1 or 2. config SOUND_TRIX tristate "MediaTrix AudioTrix Pro support" help Answer Y if you have the AudioTriX Pro sound card manufactured by MediaTrix. config TRIX_HAVE_BOOT bool "Have TRXPRO.HEX firmware file" depends on SOUND_TRIX=y && !STANDALONE help The MediaTrix AudioTrix Pro has an on-board microcontroller which needs to be initialized by downloading the code from the file TRXPRO.HEX in the DOS driver directory. If you don't have the TRXPRO.HEX file handy you may skip this step. However, the SB and MPU-401 modes of AudioTrix Pro will not work without this file! config TRIX_BOOT_FILE string "Full pathname of TRXPRO.HEX firmware file" depends on TRIX_HAVE_BOOT default "/etc/sound/trxpro.hex" help Enter the full pathname of your TRXPRO.HEX file, starting from /. config SOUND_MSS tristate "Microsoft Sound System support" ---help--- Again think carefully before answering Y to this question. It's safe to answer Y if you have the original Windows Sound System card made by Microsoft or Aztech SG 16 Pro (or NX16 Pro). Also you may say Y in case your card is NOT among these: ATI Stereo F/X, AdLib, Audio Excell DSP16, Cardinal DSP16, Ensoniq SoundScape (and compatibles made by Reveal and Spea), Gravis Ultrasound, Gravis Ultrasound ACE, Gravis Ultrasound Max, Gravis Ultrasound with 16 bit option, Logitech Sound Man 16, Logitech SoundMan Games, Logitech SoundMan Wave, MAD16 Pro (OPTi 82C929), Media Vision Jazz16, MediaTriX AudioTriX Pro, Microsoft Windows Sound System (MSS/WSS), Mozart (OAK OTI-601), Orchid SW32, Personal Sound System (PSS), Pro Audio Spectrum 16, Pro Audio Studio 16, Pro Sonic 16, Roland MPU-401 MIDI interface, Sound Blaster 1.0, Sound Blaster 16, Sound Blaster 16ASP, Sound Blaster 2.0, Sound Blaster AWE32, Sound Blaster Pro, TI TM4000M notebook, ThunderBoard, Turtle Beach Tropez, Yamaha FM synthesizers (OPL2, OPL3 and OPL4), 6850 UART MIDI Interface. For cards having native support in VoxWare, consult the card specific instructions in <file:Documentation/sound/oss/README.OSS>. Some drivers have their own MSS support and saying Y to this option will cause a conflict. If you compile the driver into the kernel, you have to add "ad1848=<io>,<irq>,<dma>,<dma2>[,<type>]" to the kernel command line. config SOUND_MPU401 tristate "MPU-401 support (NOT for SB16)" ---help--- Be careful with this question. The MPU401 interface is supported by all sound cards. However, some natively supported cards have their own driver for MPU401. Enabling this MPU401 option with these cards will cause a conflict. Also, enabling MPU401 on a system that doesn't really have a MPU401 could cause some trouble. If your card was in the list of supported cards, look at the card specific instructions in the <file:Documentation/sound/oss/README.OSS> file. It is safe to answer Y if you have a true MPU401 MIDI interface card. If you compile the driver into the kernel, you have to add "mpu401=<io>,<irq>" to the kernel command line. config SOUND_PAS tristate "ProAudioSpectrum 16 support" ---help--- Answer Y only if you have a Pro Audio Spectrum 16, ProAudio Studio 16 or Logitech SoundMan 16 sound card. Answer N if you have some other card made by Media Vision or Logitech since those are not PAS16 compatible. Please read <file:Documentation/sound/oss/PAS16>. It is not necessary to add Sound Blaster support separately; it is included in PAS support. If you compile the driver into the kernel, you have to add "pas2=<io>,<irq>,<dma>,<dma2>,<sbio>,<sbirq>,<sbdma>,<sbdma2> to the kernel command line. config PAS_JOYSTICK bool "Enable PAS16 joystick port" depends on SOUND_PAS=y help Say Y here to enable the Pro Audio Spectrum 16's auxiliary joystick port. config SOUND_PSS tristate "PSS (AD1848, ADSP-2115, ESC614) support" help Answer Y or M if you have an Orchid SW32, Cardinal DSP16, Beethoven ADSP-16 or some other card based on the PSS chipset (AD1848 codec + ADSP-2115 DSP chip + Echo ESC614 ASIC CHIP). For more information on how to compile it into the kernel or as a module see the file <file:Documentation/sound/oss/PSS>. If you compile the driver into the kernel, you have to add "pss=<io>,<mssio>,<mssirq>,<mssdma>,<mpuio>,<mpuirq>" to the kernel command line. config PSS_MIXER bool "Enable PSS mixer (Beethoven ADSP-16 and other compatible)" depends on SOUND_PSS help Answer Y for Beethoven ADSP-16. You may try to say Y also for other cards if they have master volume, bass, treble, and you can't control it under Linux. If you answer N for Beethoven ADSP-16, you can't control master volume, bass, treble and synth volume. If you said M to "PSS support" above, you may enable or disable this PSS mixer with the module parameter pss_mixer. For more information see the file <file:Documentation/sound/oss/PSS>. config PSS_HAVE_BOOT bool "Have DSPxxx.LD firmware file" depends on SOUND_PSS && !STANDALONE help If you have the DSPxxx.LD file or SYNTH.LD file for you card, say Y to include this file. Without this file the synth device (OPL) may not work. config PSS_BOOT_FILE string "Full pathname of DSPxxx.LD firmware file" depends on PSS_HAVE_BOOT default "/etc/sound/dsp001.ld" help Enter the full pathname of your DSPxxx.LD file or SYNTH.LD file, starting from /. config SOUND_SB tristate "100% Sound Blaster compatibles (SB16/32/64, ESS, Jazz16) support" ---help--- Answer Y if you have an original Sound Blaster card made by Creative Labs or a 100% hardware compatible clone (like the Thunderboard or SM Games). For an unknown card you may answer Y if the card claims to be Sound Blaster-compatible. Please read the file <file:Documentation/sound/oss/Soundblaster>. You should also say Y here for cards based on the Avance Logic ALS-007 and ALS-1X0 chips (read <file:Documentation/sound/oss/ALS>) and for cards based on ESS chips (read <file:Documentation/sound/oss/ESS1868> and <file:Documentation/sound/oss/ESS>). If you have an SB AWE 32 or SB AWE 64, say Y here and also to "AWE32 synth" below and read <file:Documentation/sound/oss/INSTALL.awe>. If you have an IBM Mwave card, say Y here and read <file:Documentation/sound/oss/mwave>. If you compile the driver into the kernel and don't want to use isapnp, you have to add "sb=<io>,<irq>,<dma>,<dma2>" to the kernel command line. You can say M here to compile this driver as a module; the module is called sb. config SOUND_YM3812 tristate "Yamaha FM synthesizer (YM3812/OPL-3) support" ---help--- Answer Y if your card has a FM chip made by Yamaha (OPL2/OPL3/OPL4). Answering Y is usually a safe and recommended choice, however some cards may have software (TSR) FM emulation. Enabling FM support with these cards may cause trouble (I don't currently know of any such cards, however). Please read the file <file:Documentation/sound/oss/OPL3> if your card has an OPL3 chip. If you compile the driver into the kernel, you have to add "opl3=<io>" to the kernel command line. If unsure, say Y. config SOUND_UART6850 tristate "6850 UART support" help This option enables support for MIDI interfaces based on the 6850 UART chip. This interface is rarely found on sound cards. It's safe to answer N to this question. If you compile the driver into the kernel, you have to add "uart6850=<io>,<irq>" to the kernel command line. config SOUND_AEDSP16 tristate "Gallant Audio Cards (SC-6000 and SC-6600 based)" ---help--- Answer Y if you have a Gallant's Audio Excel DSP 16 card. This driver supports Audio Excel DSP 16 but not the III nor PnP versions of this card. The Gallant's Audio Excel DSP 16 card can emulate either an SBPro or a Microsoft Sound System card, so you should have said Y to either "100% Sound Blaster compatibles (SB16/32/64, ESS, Jazz16) support" or "Microsoft Sound System support", above, and you need to answer the "MSS emulation" and "SBPro emulation" questions below accordingly. You should say Y to one and only one of these two questions. Read the <file:Documentation/sound/oss/README.OSS> file and the head of <file:sound/oss/aedsp16.c> as well as <file:Documentation/sound/oss/AudioExcelDSP16> to get more information about this driver and its configuration. config SC6600 bool "SC-6600 based audio cards (new Audio Excel DSP 16)" depends on SOUND_AEDSP16 help The SC6600 is the new version of DSP mounted on the Audio Excel DSP 16 cards. Find in the manual the FCC ID of your audio card and answer Y if you have an SC6600 DSP. config SC6600_JOY bool "Activate SC-6600 Joystick Interface" depends on SC6600 help Say Y here in order to use the joystick interface of the Audio Excel DSP 16 card. config SC6600_CDROM int "SC-6600 CDROM Interface (4=None, 3=IDE, 1=Panasonic, 0=?Sony?)" depends on SC6600 default "4" help This is used to activate the CD-ROM interface of the Audio Excel DSP 16 card. Enter: 0 for Sony, 1 for Panasonic, 2 for IDE, 4 for no CD-ROM present. config SC6600_CDROMBASE hex "SC-6600 CDROM Interface I/O Address" depends on SC6600 default "0" help Base I/O port address for the CD-ROM interface of the Audio Excel DSP 16 card. config SOUND_VIDC tristate "VIDC 16-bit sound" depends on ARM && (ARCH_ACORN || ARCH_CLPS7500) help 16-bit support for the VIDC onboard sound hardware found on Acorn machines. config SOUND_WAVEARTIST tristate "Netwinder WaveArtist" depends on ARM && ARCH_NETWINDER help Say Y here to include support for the Rockwell WaveArtist sound system. This driver is mainly for the NetWinder. config SOUND_KAHLUA tristate "XpressAudio Sound Blaster emulation" depends on SOUND_SB endif # SOUND_OSS config SOUND_SH_DAC_AUDIO tristate "SuperH DAC audio support" depends on CPU_SH3 && HIGH_RES_TIMERS config SOUND_SH_DAC_AUDIO_CHANNEL int "DAC channel" default "1" depends on SOUND_SH_DAC_AUDIO
| .. | |||||
| dmasound | |||||
| Kconfig | |||||
| Makefile |